Multi-tech-systems MTASR1-100 Manual do Utilizador Página 34
- Página / 207
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MTASR1-100 Owner’s Manual
34
4.1 Introduction
This chapter covers procedures for loading the software and configuring your RouteFinder
100
. There are
several paths the software loading process can take depending on the protocol that you are using, whether the
WAN is a real port or one or many virtual ports used in frame relay. The first path that you will see is using
IPX as the protocol and the WAN device providing the access to public telephone service. The second path is
again using IPX, but changing the WAN device to virtual WANs. The third and fourth paths just change the
protocol and follow the same process with the WAN device and virtual WANs.
You will not have to go through all the procedures for any application. The software loading is organized so
that everybody uses the common procedures at the beginning. Then you break off depending on your
protocol. You break off again depending on how your WAN is used. Finally you come back to some common
procedures that every body has to use.
4.2 Loading Software
Common Procedure
1 Turn on your PC connected to the Command Port of your RouteFinder
100
and run Windows®.
2 Create a backup copy of your RouteFinder
100
software diskettes before you install the software. Store the
master diskettes in a safe place and install the RouteFinder
100
software using the backup copy.
3 Inset the backup disk, labeled RouteFinder
100
Disk 1, into the floppy drive.
4 Click on the File Menu in your Program Manager.
5 Click on Run. The Run dialog box is displayed.
6 Type a:\install or b:\install (depending on the location of your floppy disk drive) in the Command Line
field, and then click on OK.
7 The RouteFinder
100
Setup - Select Directories dialog box is displayed.
If you are installing from Drive A: and your Destination Directory is the default directory, click on O.K. to
continue.
8 The Installing RouteFinder
100
dialog box is displayed.
Click on Install to continue installation, at any time you may click on Abort if you wish to cancel the
install.
- Model MTASR1-100 1
- Single WAN 1
- Multi-Protocol Router 1
- Owner’s Manual 1
- Owner's Manual 2
- 82052804 Revision E 2
- Contents 3
- 1.1 Introduction 8
- 1.2 About This Manual 8
- 1.3 Network Overview 10
- 1.3.1 Packet 11
- 1.3.2 Network Address 12
- 1.4 Typical Applications 14
- 1.4.1 Typical IP Application 14
- 1.4.3 Subscription 16
- 1.4.4 Configuration 17
- 1.5 Specifications 21
- Requirement 21
- 2.1 Introduction 24
- 2.2 Front Panel 24
- 2.3 Back Panel 25
- 2.4 Shunts 26
- Chapter 3 - Installation 27
- 3.1 Introduction 28
- 3.2 Unpacking 28
- 3.3 Installation 29
- 3.4 V.35 Shunt Procedure 30
- 4.1 Introduction 34
- 4.2 Loading Software 34
- 5.1 Introduction 44
- 5.2 Router Configuration 44
- 5.2.1 Setup Menu 44
- 5.2.2 Protocol Stacks 45
- 5.2.3 Device Drivers 45
- 5.2.4 Other Setup 46
- 5.2.5 Actions 46
- Add A New Network 49
- Delete a Network 49
- Save Change 49
- IP General Setup 50
- IP RIP= [enabled 50
- Modify a Network 58
- Remote Port Setup 61
- 5.2.10 WAN Port Setup 63
- Connection Method 64
- Terminal Server 64
- WAN General Setup 65
- WAN Message Printing Control 65
- Script Printing 65
- Modem Control 65
- Modem Type 65
- 5.2.11 Frame Relay Setup 66
- Error Threshold (N392) 67
- Monitored Events Count (N393) 67
- Adding a DLCI 69
- Deleting a DLCI 69
- 5.2.13 Applications Setup 71
- Enable TFTP Server 72
- Enable =[enable I disabled] 73
- Default Logon Screen 73
- 5.2.14 Filtering 74
- ICMP Filtering 77
- IPX Filtering 77
- Default Action 77
- Filtering Entries List 78
- 5.2.15 Diagnostics 80
- EtherNet Port Test 81
- WAN Port Test 81
- WAN Link Test 81
- 5.3 Download Default Setup 82
- 5.4 Download Firmware Update 84
- 5.5 Configuration Port Setup 86
- 5.6 WAN Device Configuration 88
- 5.7 Remote User Data Base 90
- 5.7.1 Add User 91
- 6.1 Introduction 94
- 6.2 Two RouteFinder 94
- MTASR1-100 Owner’s Manual 140
- 7.1 Introduction 148
- Chapter 8 - Router Management 153
- 8.1 Introduction 154
- 8.2.1 View SNMP Parameters 155
- 8.2.2 Set SNMP Parameters 156
- 8.2.4 Refresh SNMP Object 158
- 8.2.6 Property Sheet 159
- 8.2.8 Agent Name Dialog 159
- 8.2.9 Commands 160
- Window menu commands 161
- 8.3 Telnet Management 162
- 8.3.1 Router Configuration 163
- Router Configuration 164
- Applications 166
- WAN Device Configuration 168
- Remote User Database 168
- 9.1 Introduction 170
- 9.2 Installing MCSI 170
- <Line Type> 178
- <SpecificName> 178
- <GeneralName> 178
- <ServerName> 178
- Software 179
- 10.4 Service 195
- 10.5 The Multi-Tech BBS 195
- 10.5.2 To Download a file 195
- 10.6 About CompuServe 196
- 10.7 About the Internet 196
- Appendixes 197
- Appendix A - Cabling Diagrams 198
- Link Cables 199
- Appendix B - Script Language 200
- Script Language Grammar 201
Manuais e produtos relacionados com Hardware Multi-tech-systems MTASR1-100
(74 páginas)Rockwell Automation 440G Trojan T15 Tongue Operated Guard Interlock Sw manuály
Uživatelské manuály a uživatelské příručky pro Zařízení Rockwell Automation 440G Trojan T15 Tongue Operated Guard Interlock Sw.
Poskytujeme 1 manuály pdf Rockwell Automation 440G Trojan T15 Tongue Operated Guard Interlock Sw ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais