Multi-tech-systems CDMA Wireless Modem Manual do Utilizador Página 69
- Página / 195
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 9 – Supplementary Service Commands
Multi-Tech Systems, Inc. CDMA Wireless AT Commands - PN S000294C 69
Calling Line Identification Restriction +CLIR
Description: This command allows control of the outgoing caller ID restriction supplementary service.
Values: <mode>: sets the caller ID restriction for outgoing calls
0: Outgoing Caller ID works normally, according to the subscription of the Caller ID
service.
1: Outgoing Caller ID is restricted. The called party will see ‘Restricted’ on their Caller ID
display.
Note that this command works by automatically pre-pending a *67 to the outgoing dialing
string. Thus, this command will only work on CDMA networks that recognize a *67 to
suppress outgoing caller ID. Also, the original dialing string cannot be longer than 29
characters in length.
Syntax: Command syntax: AT+CLIR=<mode>
Command Possible Responses
AT+CLIR=1
Note: Restrict outgoing caller ID.
OK
Note: Command valid
AT+CLIR?
Note: Ask for current functionality
+CLIR :<mode>
OK
Note: <mode> as defined below
Calling Line Identification Presentation +CLIP
Description: This command allows control of the incoming caller ID presentation supplementary service.
When presentation of the CLI (Calling Line Identification) is enabled (and the carrier allows),
+CLIP response is returned after the RING unsolicited result code. By default, +CLIP is
enabled.
Values: <mode>: parameter enable or disables the caller ID unsolicited command
0: Disable
1: Enable
Syntax: Command syntax: AT+CLIP=<mode>
Command Possible Responses
AT+CLIP=1
Note: Enable CLIP
OK
Note: CLIP is enabled
AT+CLIP?
Note: Ask for current functionality
+CLIP:<mode>
OK
Note: <mode> defined as below
RING
Note: Incoming call
+CLIP: “8585551212”,129
Note: Incoming call with number presentation
AT+CLIP=0
Note: Disable CLIP presentation
OK
Note: Command valid
- Contents 3
- CHAPTER 1 - INTRODUCTION 11
- Definitions 12
- Chapter 1 - Introduction 13
- Line Settings 14
- Command Line 14
- Key Press or Release +CKEV 17
- Mode Preference +COPS 18
- Call Answered +WANS 20
- Call Connected +WCNT 20
- Call Ended +WEND 20
- Flash Indication +WFSH 21
- General Indicator +WIND 22
- Call Originated +WORG 23
- Roaming Indication +WROM 24
- Emergency Mode +WSOS 24
- Current NAM Change +WNAM 25
- Voice Mail Indicator +WVMI 25
- Power Save +WSPS 26
- HAPTER 4 - GENERAL COMMANDS 27
- Clock Management +CCLK 31
- Ring Melody Playback +CRMP 31
- View Modem Timers +WTMR 33
- Modem Serial Number +WMSN 33
- Dial Command D 34
- Hang-Up Command H 35
- Answer a Call A 36
- Remote Disconnection 36
- DTMF Signals +VTD, +VTS 37
- Automatic Answer S0 38
- Incoming Call Bearer +CICB 39
- Microphone Gain +VGT 40
- Volume Gain Control +VGR 40
- Echo Cancellation +ECHO 42
- TTY Mode +WTTY 43
- Band Preference +WBND 45
- Roam Preference +WRMP 46
- Change NAM Selection +WNAM 48
- Read Current NAM +WCNM 48
- Enter PIN +CPIN 51
- Enter PIN2 +CPIN2 52
- Change Password +CPWD 54
- Card Identification +CCID 54
- Parameters Definition 55
- Read Message +CMGR 59
- List Message +CMGL 61
- Send Message +CMGS 62
- Delete Message +CMGD 64
- Message Overwriting +WMGO 66
- Change SMS Status +WUSS 66
- Call Forwarding +CCFC 68
- Command Possible Responses 70
- CHAPTER 10 - DATA COMMANDS 72
- Cellular Result Codes +CRC 73
- Fixed DTE Rate +IPR 76
- Set DCD Signal &C 77
- Save Configuration &W 81
- Phonebook Read +CPBR 85
- Phonebook Search +CPBP 85
- Avoid Phonebook Init +WAIP 86
- (GPS) AT COMMANDS 87
- Read GPIO Value +WIOR 97
- Write GPIO Value +WIOW 97
- Play Tone +WTONE 98
- Play DTMF Tone +WDTMF 99
- Hardware Version +WHWV 99
- Select Voice Gain +WSVG 100
- Status Request +WSTR 100
- Ring Indicator Mode +WRIM 101
- 32kHz Sleep Mode +W32K 101
- Software Version +WSSW 102
- Custom Character Set +WCCS 103
- CPHS Command +CPHS 104
- Reset +WRST 105
- Set Standard Tone +WSST 105
- Security PIN +WPIN 107
- Minute Alert +WMBP 108
- CHAPTER 15 - SIM TOOLKIT 111
- +STSF=X,XXXXXXXX 112
- Chapter 15 – SIM TOOLKIT 113
- Error Codes 115
- Example 123
- Set IMSI +WIMI 125
- SID and NID +WSID 125
- Slot Cycle Index +WSCI 126
- Packet Dial String +WPDS 127
- Commit Changes +WCMT 128
- Read SID/NID Entries +WSNR 129
- Service Programming Example 130
- Remote Async/Fax Command X 131
- Select Tone Dialing T 131
- Select Pulse Dialing P 132
- Error Control Report +ER 134
- Modulation Selection +MS 137
- V.18 Selection +MV18S 139
- Cellular Extension +CXT 139
- Battery Charge +CBC 142
- Serving System +CSS 144
- CHAPTER 18 – FAX PARAMETERS 148
- IS-707.3 Fax Parameters 149
- IS-707.3 Fax Action Commands 149
- CDMA OPERATION 150
- Set DM Baud Rate $QCDMR 156
- SCRM’ing Selection $QCSCRM 157
- R-SCH Selection $QCTRTL 157
- R-SCH Selection $QCMIP 158
- MIP Selection $QCMIPP 159
- Specific Error Result Codes 167
- Final Result Codes 167
- Intermediate Result Codes 168
- Parameters Storage 168
- Code Meaning 169
- Example with Incoming Calls 171
- When the MS is Powered On 172
- (Chapter 3) 174
- Excess SPC Failures +WLCK 186
- Signal Quality +CSQ 188
- Facility Lock +CLCK 189
- Boot URL +WBURL 192
- Trusted Domain +WTDMN 192
- Proxy Address +WDPXY 193
Manuais e produtos relacionados com Hardware Multi-tech-systems CDMA Wireless Modem
(8 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.174 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais