Multi-tech-systems ISI5634PCI/4/8 Manual do Utilizador

ISI5634PCI/4/8User Guide

10ISI5634PCI/4/8 User GuideTechnical SpecificationsComputer Requirements Pentium®- based PC or compatible with PCI Bus Architecture One of these ope

100ISI5634PCI/4/8 User Guide78 * CONNECT 48000 Connected at 48000 bps, 56K rate79 * CONNECT 50000 Connected at 50000 bps, 56K rate80 * CONNECT 52000 C

Chapter 5Warranty, Service, and Tech Support

102ISI5634PCI/4/8 User GuideSoftware User License AgreementThe ISI drivers and firmware are licensed by Multi-Tech Systems, Inc.to the original end-us

103Chapter 5—Warranty, Service, and Tech SupportLicensee agrees to implement sufficient security measures to protectMulti-Tech Systems, Inc. propriet

104ISI5634PCI/4/8 User GuideLimited WarrantyMulti-Tech Systems, Inc. (MTS) warrants that its products will be freefrom defects in material or workmans

105Chapter 5—Warranty, Service, and Tech SupportTech SupportMulti-Tech has an excellent staff of technical support personnelavailable to help you get

106ISI5634PCI/4/8 User GuideServiceIf your tech support specialist decides that service is required, yourunit may be sent (freight prepaid) to our fac

Appendices

108ISI4608 Owner's ManualAppendix ARegulatory InformationFCC Regulations for Telephone Line Interconnection1. This equipment complies with part

109Appendix A - Base I/O Address Switch Settingsoperation of the equipment. If this happens, the telephonecompany will provide advance notice in orde

Chapter 2—Hardware Installation

110ISI4608 Owner's ManualClass A StatementFCC Part 15This equipment has been tested and found to comply with the limits fora Class A digital devi

111Appendix A - Base I/O Address Switch SettingsCanadian Limitations Notice: Ringer EquivalenceNumberNotice: The ringer equivalence number (REN) assi

112ISI4608 Owner's ManualFax Branding StatementThe Telephone Consumer Protection Act of 1991 makes it unlawful forany person to use a computer or

113Appendix A - Base I/O Address Switch SettingsNew Zealand Telecom Warning NoticeUse of pulse dialing, when this equipment is connected to the sameli

114ISI4608 Owner's Manual

Index

116ISI5634PCI/4/8 User GuideIndexSymbols11-bit mode 9056K operationdigital loss when used with PBX 98disabling the auto rate 98maximum connect speed 9

117IndexQ80S= 81S? 81T81V81W81X82Y82Z82autoanswer 76, 95Auxiliary Relay Control command 84Bbackspace character, setting 96base I/O address 10baud rate

118ISI5634PCI/4/8 User GuideData Carrier Detect command 83Data Compression Control com-mand 89data mode 76, 80Data Set Ready Control command 84Data Te

119Indexinstallationactivating portsin SCO Open Server 5 59hardware 12ISI5634PCI driverin Linux 60in Netware 51in SCO 52in Windows 2000 18in Windows 9

12ISI5634PCI/4/8 User GuideIntroductionIncluded in this chapter are two sets of instructions for installing theMulti-Tech ISI5634PCI card in your PCI

120ISI5634PCI/4/8 User Guidemodem installLinux 64Linux RPM 70Netware 52SCO 59Windows 2000 26Windows 95/98/Me 47Windows NT 37Modem Port Flow Control co

121IndexResult Codes Enable/Disable com-mand 80retrain 82Return Online to Data Mode com-mand 80rings, setting number of 95ROM checksum 79SS-registers

122ISI5634PCI/4/8 User GuideTtech support 105technical specifications 10temperature 10testing the modem 85Tone Dialing command 81tones, dialing 96Tran

13Chapter 2—Hardware Installation4. To avoid damaging the ISI5634PCI card and your PC, make sureyour computer and any peripheral equipment connected t

14ISI5634PCI/4/8 User GuideInstalling the ISI5634PCI card WITH the auxiliary module:1. The auxiliary module attaches to the ISI5634PCI card. If youalr

15Chapter 2—Hardware Installation7. Before installing the ISI5634PCI card, carefully line up the pin-outconnectors of the ISI5634PCI card with the pi

16ISI5634PCI/4/8 User Guide11. Fasten the retaining bracket to computer chassis and replacecover.12. Plug one end of the phone cable into each modems

Chapter 3 — Software/Driver Installation

18ISI5634PCI/4/8 User GuideIntroductionThe ISI5634PCI card ships with drivers for each of the followingoperating systems: Windows® 2000, Windows NT, W

19Chapter 3—Software/Driver Installationhandling the ISI5634PCI board (the board should be kept in itsshipping bag until used). During installation, h

User GuideModel ISI5634PCI/4/8P/N S0000109, Revision DThis publication may not be reproduced, in whole or in part, without priorexpressed written perm

20ISI5634PCI/4/8 User Guide6. The Install Hardware Device Drivers screen appears. Select"Search for a suitable driver ..." and click Next.7

21Chapter 3—Software/Driver Installation8. The Driver File Search Results screen appears.Click Next.9. A progress screen will appear briefly while fil

22ISI5634PCI/4/8 User Guide10. A completion screen will appear.Click Finish.11. Immediately after the ISI driver installation has been completed,anot

23Chapter 3—Software/Driver InstallationA second sequence of installation wizard screens appears. Thissequence of screens deals with the setting up

24ISI5634PCI/4/8 User Guide13. The Locate Driver Files screen appears (Windows 2000 isseeking the ISI Port device driver). Select CD-ROM drives an

25Chapter 3—Software/Driver Installation15. A completion screen will appear. It will indicate that the firstMultiTech ISI Port has been set up suc

26ISI5634PCI/4/8 User GuideISI5634PCI for Windows 2000: Installing Modems toCOM PortsPre-Requisite: Installation of Windows 2000 driver software mus

27Chapter 3—Software/Driver Installation4. At the Install New Modem screen, click on "Don't detect mymodem ... " and click Next.5. If

28ISI5634PCI/4/8 User Guide7. The Install from Disk screen will appear.Type or browse for the file path of the modem software (forexample, E:\servcard

29Chapter 3—Software/Driver Installation9. The Install New Modem - port list screen will appear.Highlight the COM ports on which you want modems to

ContentsChapter 1—Introduction and Description ...5Introduction ...

30ISI5634PCI/4/8 User Guide11. Screens denoting the installation of modems to specific COMports will appear for each modem installed.12. A completion

31Chapter 3—Software/Driver Installation13. The Phone and Modems Options screen (Modems tab) will re-appear and display the modems that have just bee

32ISI5634PCI/4/8 User GuideISI5634PCI for Windows 2000: Installing ISI Manage-ment Software (server OSs only)If you are using a Windows 2000 Server op

33Chapter 3—Software/Driver InstallationInstalling the ISI5634PCI Card in Windows NT 3.51/4.0The following procedure describes how to install the ISI5

34ISI5634PCI/4/8 User Guide5. Click Start, Settings, Control Panel, and then double-clickNetwork. In the Network dialog box, click the Adapters tab.Cl

35Chapter 3—Software/Driver Installation7. The Insert Disk dialog box appears. Type in or browse for thepath (file directory location) of the Window

36ISI5634PCI/4/8 User Guide11. The ISI Cards dialog box appears again showing the port resourceallocation that has just been made.To add additional IS

37Chapter 3—Software/Driver Installation13. After bindings are reviewed and stored, the Network SettingsChange dialog box appears. Click Yes to reboot

38ISI5634PCI/4/8 User Guide4. The Install New Modem - Models dialog box appears.Highlight ISI5634PCI-8 PCI 56K Modem and click Next.5. Select ports

39Chapter 3—Software/Driver Installation6. After the modems install to the ports, click Finish to return to theGeneral tab.7. To view COM port assignm

Linux Driver for ISI5634PCI-4/8 ... 60LINUX: Pre-Installation Issues ...

40ISI5634PCI/4/8 User Guide8. When finished, close the Modem Properties dialog box. Themessage below appears asking if you want to configure Dial-UpN

41Chapter 3—Software/Driver Installation11. The Remote Access Setup dialog box displays again. Repeatsteps 9 and 10 until all modems are added.12. Wh

42ISI5634PCI/4/8 User GuideRemoving ISI5634PCI Driver in Windows NT 3.51/4.01. Click Start, Settings, Control Panel, and then double-clickNetwork.2. T

43Chapter 3—Software/Driver Installation6. (Follow either 6A or 6B, but not both.)A. From Windows Explorer, open the 95-98-Me directory on theCD-ROM (

44ISI5634PCI/4/8 User Guide9. Under Select Type of Card, do not check the Install ISA Card box.Click Next.10. A completion screen appears.11. When p

45Chapter 3—Software/Driver Installation13. The next screen asks, What do you want Windows to do? Click onSearch for the best driver for your device.

46ISI5634PCI/4/8 User Guide18. To view the COM ports, click Control Panel and double-clickSystem. The System Properties dialog box appears.The MultiTe

47Chapter 3—Software/Driver InstallationInstalling Modems to COM Ports in Win 95 /98/Me1. Click Start, Settings, Control Panel, and then double-click

48ISI5634PCI/4/8 User Guide3. The Install New Modem - Manufacturers dialog box appears. Inthe Manufacturers list, scroll down and highlight "Mul

49Chapter 3—Software/Driver Installation5. When installing the first ISI modem, the Location Informationscreen will appear (it does not appear when a

Chapter 1—Introduction and Description

50ISI5634PCI/4/8 User Guide7. Return to the General tab to view COM port assignments (andmake changes if necessary).8. Click Add and repeat installati

51Chapter 3—Software/Driver InstallationRemoving the ISI5634PCI Driver (Windows 95/98/Me)1. Click Settings, Control Panel, and then double-click Add/R

52ISI5634PCI/4/8 User GuideIf you have downloaded the ISI driver from the MultiTech web siteonto a diskette, use this command:COPY A:\NOVELL\AIOISIX.N

53Chapter 3—Software/Driver InstallationThis present installation section is task-oriented with minimalexplanation of procedural steps. The section M

54ISI5634PCI/4/8 User Guide4. Copy the untarred (inflated or non-compressed) files to a floppy disk# cd /isi/unifiedinstimg301#scosh- Select Manager.-

55Chapter 3—Software/Driver Installation5. Select as the Media Device Floppy Disk Drive.6. Select Continue.7. Highlight Multi-Tech ISA/PCI ... and

56ISI5634PCI/4/8 User Guide1. This text appears on the screen:You can install up to 4 ISA/PCI cards in asystem. The PCI cards will be autodetectedon b

57Chapter 3—Software/Driver InstallationISICOM. The default prefix for the ttyports is ttyl. The default prefix for theprinter is prnl. Is this acc

58ISI5634PCI/4/8 User Guideprinting). Specify a unique printer base name (printer parametersare outlined in the Multi_Setup Utility section in this m

59Chapter 3—Software/Driver InstallationActivating Ports in SCO Open Server 5SCO Open Server 5 provides a device database that monitors theactivity of

6ISI5634PCI/4/8 User GuideIntroductionWelcome to the world of data communications. You have acquired oneof the finest intelligent data and fax modems

60ISI5634PCI/4/8 User Guide5. Repeat this command for each port you want to activate, using thelower case letter for local terminal use or upper case

61Chapter 3—Software/Driver Installationissued from time to time.The 'make' utility, GNU C compiler, and the kernel sources need to beinstal

62ISI5634PCI/4/8 User GuideNOTE: To read from a DOS formatted floppy, a kernel with support forthe FAT file system (either statically linked in the ke

63Chapter 3—Software/Driver InstallationTo view busy IRQs, enter:cat /proc/interruptsYou must load the driver before you can load the firmware. You c

64ISI5634PCI/4/8 User Guidefirst port on the first card). Save the configuration for a particular portusing the 'save setup as' menu optio

65Chapter 3—Software/Driver Installation- /dev/ttyM4a TO /dev/ttyM4h for the fourth cardDevices mapped for modem cards (ISI5634PCI-4 andISI5634PCI-8

66ISI5634PCI/4/8 User GuideNote: A base I/O address of 0, e.g., ISIBaseX=oxo, or omission of theseparameters for any card X, disables that particular

67Chapter 3—Software/Driver Installation rm ttyM1* rm ttyM2* rm ttyM3* rm ttyM4*RedHat Linux 6.2/7.0 RPM Drivers forISI5634PCI-4/8

68ISI5634PCI/4/8 User Guide3. List the RPM files on the CD-ROM using this command:lsLINUX-RPM: Copying the driver from a floppyThe ISI driver .rpm fil

69Chapter 3—Software/Driver InstallationRPM, you will need to use the --force option in the RPM command asin step 5b below.5a. For RPM version 6.2:

7Chapter 1—Introduction and Descriptiondigital to analog only once before it reaches your modem. Upstreamtransmissions and transmissions between clien

70ISI5634PCI/4/8 User GuideLINUX-RPM: Verifying the portsTo test the installation, you can use the terminal program minicom.Use the command minicom

71Chapter 3—Software/Driver InstallationFor the ISI5634PCI-8, it uses the following:- /dev/ttyM1a TO /dev/ttyM1h for the first card- /dev/ttyM2a TO /d

72ISI5634PCI/4/8 User GuideHOWTO) explains in detail the procedure for configuring a Linuxmachine as a PPP server. This information is also available

73Chapter 3—Software/Driver Installation To load a custom configuration that was saved using the &Wcommand, use ATZ. Note that the Z command must

74ISI5634PCI/4/8 User GuideReferencesISI5634PCI User GuideThe ISI5634PCI Quick Start Guide is a condensed version of this UserGuide in printed form.

Chapter 4AT Commands, S-Registers, & Result Codes

76ISI5634PCI/4/8 User GuideAT CommandsAT commands are used to control the operation of your modem. Theyare so called because each command must be prec

77Chapter 4—AT Commands, S-Registers, Result Codesconnecting to another modem. For a table of valid result codes, seeResult Codes at the end of this c

78ISI5634PCI/4/8 User GuideCommand: Cn Carrier ControlValues: n = 1Default: 1Description: C0 Transmit carrier always off. (Not supported.)C1 Normal

79Chapter 4—AT Commands, S-Registers, Result CodesCommand: DS=y Dial Stored Telephone NumberValues: n = 03Default: noneDescription: Dial a number pre

8ISI5634PCI/4/8 User GuideThe processor, along with 256K bytes of RAM, works to allocateresources dynamically to the most active port. The ISI then

80ISI5634PCI/4/8 User GuideI11 Display diagnostic information for the last modem con-nection, such as DSP and firmware version, link type,line speed,

81Chapter 4—AT Commands, S-Registers, Result CodesCommand: Sr=n Set Register ValueValues: r = S-register number; n variesDefault: NoneDescription: Set

82ISI5634PCI/4/8 User GuideCommand: Xn Result Code SelectionValues: n = 07Default: 4Description: X0 Basic result codes (e.g., CONNECT); does not look

83Chapter 4—AT Commands, S-Registers, Result CodesCommand: &Cn Data Carrier Detect (DCD) ControlValues: n = 0 or 1Default: 1Description: &C0 F

84ISI5634PCI/4/8 User GuideCommand: &Jn Auxiliary Relay ControlValues: n = 0Default: 0Description: &J0 The auxiliary relay is never closed.&am

85Chapter 4—AT Commands, S-Registers, Result CodesCommand: &Tn V.54 Test CommandsValues: n = 0, 1, 3 or 6Default: NoneDescription: &T0 Abort.

86ISI5634PCI/4/8 User GuideCommand: &Zy=x Store Dialing CommandValues: y = 03 (callback security disabled) or 029 (callbacksecurity enabled)x =

87Chapter 4—AT Commands, S-Registers, Result CodesCommand: \Kn Break ControlValues: n = 05Default: 5Description: Controls the response of the modem t

88ISI5634PCI/4/8 User GuideCommand: \Nn Error Correction Mode SelectionValues: n = 05, or 7Default: 3Description: \N0 Non-error correction mode with

89Chapter 4—AT Commands, S-Registers, Result CodesDescription: \V0 Disable the appending of the protocol result code tothe DCE speed.\V1 Enable the ap

9Chapter 1—Introduction and DescriptionWhat Is in Your Modem Package?Your modem package has several components. Make sure you havethem all before tryi

90ISI5634PCI/4/8 User Guide%DC1 The modem ignores AT commands.Note: The modem responds to AT%DC for 10 secondsafter power-up.Command: %En Fallback and

91Chapter 4—AT Commands, S-Registers, Result CodesCommand: #CBDn Callback DelayValues: n = 0255Default: 15Description: Sets the length of time (in s

92ISI5634PCI/4/8 User Guide#CBP0 No parity.#CBP1 Odd parity.#CBP2 Even parity.Command: #CBRyCallback Security ResetValues: y = 029Default: NoneDescri

93Chapter 4—AT Commands, S-Registers, Result Codesto ten command character. Then press ENTER. Usedmostly to issue hangup command: +++ATH<cr>.Com

94ISI5634PCI/4/8 User GuideAbout DTMFDTMF (dual tone multi frequency) is the signal to the phone companythat you generate when you press an ordinary t

95Chapter 4—AT Commands, S-Registers, Result CodesDual Tone Multi-frequency (DTMF) was a technique proposed by thephone company to replace pulse dial

96ISI5634PCI/4/8 User GuideS5 decimal 032 8 (^H) Sets ASCII code for the backspace33127 character. Values greater than 32disable backspace.S6 second

97Chapter 4—AT Commands, S-Registers, Result Codeswhich the modem attempts to connect.0 = maximum modem speed1 = reserved2 = 1200/75 bps3 = 300 bps4 =

98ISI5634PCI/4/8 User Guide12 = 52000 bps13 = 54000 bps14 = 56000 bpsS42 decimal 01 1 Enables/disables the 56K auto rate.When 56K auto is disabled, f

99Chapter 4—AT Commands, S-Registers, Result CodesResult CodesIn command mode, ISI5634PCI modems can send responses calledresult codes to your compute