Multi-tech-systems MT5600ZDX Manual do Utilizador

1Owners ManualTMTM

10Model MT5600ZDXSafety Warnings1. Never install telephone wiring during a lightning storm.2. Never install telephone jacks in wet locations unless th

11Owners ManualInstallation ProcessThe installation of the MultiModemZDX consists of making the physicalconnections necessary to render the modem fun

12Model MT5600ZDX5. Turn on power by flipping the "ON/OFF" switch on the side of theMultiModemZDX to the "ON" position.6. Make sur

13Owners Manual Figure 2-3. MultiModemZDX Front PanelTDTransmit Data. The TD LED flashes when data is beingtransmitted (on for a space, off for

14Model MT5600ZDX 28V.34. This LED is lit when the modem is connected in V.34 mode. 14V.32bis. This LED is lit when the modem is connected in V.32bis

15Owners ManualIs Your MultiModemZDX Ready for Use?As soon as you have connected power to the modem, if youre anexperienced modem user, you may simp

16Model MT5600ZDXmodems command buffer. Once youre in terminal mode, enter AT followedby <CR> to check whether your modem is operational. If

17Owners ManualFigure 2-5. MultiModemZDX Initialization SetupOther software programs require you enter an initialization string in thesoftware modem

18Model MT5600ZDXTroubleshootingYour MultiModemZDX was thoroughly tested at the factory before it wasshipped. If you are unable to make a successful c

19Owners Manual4 Make sure you are issuing the modem commands from the data communicationssoftware, either manually in terminal mode or automatically

2Model MT5600ZDXNOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC R

20Model MT5600ZDXconflicting devices to use one of the unused IRQs. If you find an address conflict,change the address of one of the conflicting devic

21Owners Manualmodify as well. Note that you can return to the modem's default configurationby entering AT&F. If your application requires

22Model MT5600ZDXinternal dial tone; if you cant, change your modems initialization string to replaceX4 with X3, which will cause the modem to ignor

23Owners Manual4 If you have extension phones on the same line as your modem, you or someoneelse can interrupt the connection by picking up another p

24Model MT5600ZDX4 Make sure the flow control method you selected in software matches the methodselected in the modem.4 If you are running under Windo

25Owners ManualAT CommandsAT commands are the means by which you, and your communicationssoftware, are able to communicate with and configure your mo

26Model MT5600ZDXCommand: Bn Communication Standard SettingValues: n = 0 or 1Default: 0 and 1Description: B0 Select ITU-T V.22 mode when modem is at 1

27Owners ManualCommand: DS=n Dial Stored Telephone NumberValues: n = 03Default: noneDescription: Dial a number previously stored in directorynumber

28Model MT5600ZDXCommand: Ln Monitor Speaker VolumeValues: n = 0, 1, 2, or 3Default: 1Description: L0 Select low volume.L1 Select low volume.L2 Select

29Owners ManualCommand: Qn Enable/Disable Result CodesValues: n = 0 or 1Default: 0Description: Q0 Enable Result Codes.Q1 Disable Result Codes.Comman

3Owners ManualOwners Manual82068601 Revision BModel MT5600ZDXThis publication may not be reproduced, in whole or in part, without prior expressed wr

30Model MT5600ZDXCommand: Wn Connect Message ControlValues: n = 0, 1 or 2Default: 0Description: W0 Upon connection, the modem reports DTE speedonly (e

31Owners ManualCommand: Zn Modem ResetValues: n = 0 or 1Default: NoneDescription: Z0 Reset modem to profile saved by the last &Wcommand (profile

32Model MT5600ZDXCommand: &Jn Telephone Jack ControlValues: n = 0 or 1Default: NoneDescription: &J0 NA&J1 NA*This command is only included

33Owners ManualCommand: &Qn Asynchronous Communications ModeValues: n = 0, 5, or 6Defaults: 5Description: &Q0 Asynchronous with no data buff

34Model MT5600ZDXCommand: &V0 View Current ConfigurationValues: n/aDescription: Displays the active modem settings.*Reports the current (active) s

35Owners ManualCommand: &Yn Select Stored Configuration for Hard ResetValues: n = 0 or 1Default: noneDescription: &Y0 Select stored configura

36Model MT5600ZDXCommand: %7 Plug and Play Serial NumberValues: noneDefault: noneDescription: %7 Sets and stores eight serial numbers in hex format fo

37Owners ManualCommand: \Bn Transmit Break to RemoteValues: n =\B1-\B9Default: \B3Description: \B3 Break length in 100 ms units (non-error correction

38Model MT5600ZDX\K0 Clear data buffers and send break to the remotemodem.\K1 Same as \K0.\K2 Send break to remote modem immediately.\K3 Same as \K2.\

39Owners ManualCommand: +MS Select ModulationValues:Default: n/aDescription: +MS= This extended-format command selects the modula-tion, optionally en

4Model MT5600ZDXContentsChapter 1Introduction ... 6Product Description ...

40Model MT5600ZDXCommand: -SDR=n Enable/Disable Distinctive RingValues: -SDR=nDefault: 0Description: -SDR=0 Disables Distinctive Ring. Any Valid ring

41Owners ManualCommand: -Kn MNP 10 MNP Extended ServicesValues: n = 0, 1, or 2Default: 0Description: -K0 Disables V.42 LAPM to MNP 10 conversion.-K1

42Model MT5600ZDXCommand: *B View Numbers in BlacklistValues: n/aDescription: This command requests the modem to return a list ofblacklisted numbers t

43Owners Manual#CID=2 Enables Caller ID with unformatted presenta-tion. The modem will present the entire packetinformation, excluding the leading U&

44Model MT5600ZDXS-RegistersCertain Command Mode configurations are stored in memory registerscalled, S-Registers. The S command is used to assign a

45Owners ManualRegister Unit Range Default DescriptionS8 seconds 0255 2 Sets the length of a pause causedby a comma character in a dialingcommand.S9

46Model MT5600ZDXS16 General Bit Mapped Test Options Status. Indicates the Test inprogress status: Default 0.Bit 0 Local Analog Loopback0 = Disabled (

47Owners ManualS21 V.24/General Bit Mapped Options Status (Indicates the status ofcommand Options.) Default: 52 (34h)Bit 0 Set by &Jn command bu

48Model MT5600ZDXRegister Unit Range Default DescriptionS23 General Bit Mapped Options Status (Indicates the status ofcommand Options.) Default: 62 (

49Owners ManualRegister Unit Range Default DescriptionS27 Bit Mapped Options Status (Indicates the status of commandOptions.) Default: 73 (49h)Bit 0

5Owners ManualChapter 4Local Analog Loopback Test/V.54 Loop 3 .60Digital Loopback Test/V.54 Loop 2 ...61Digital Loopback Test/V.54 Loop 2 ..

50Model MT5600ZDXS29 1 minute 0255 70ms Sets the length of time, in units of10 ms, that the modem will goon-hook when it encounters aflash (!) dial m

51Owners ManualS36 Bit-Mapped Options Status (Indicates the status of commandOptions.) LAPM Failure Control Default: 7Bits 0-2 This option indicates

52Model MT5600ZDXBits 0-4 Desired line connection speed. If an invalid number is entered, thenumber is accepted into the register, but S37 will act

53Owners ManualS40 Bit-Mapped Options Status (Indicates the status of commandOptions.) Default: 104Bit 0-1 MNP Extended Services (-Kn)

54Model MT5600ZDXRegister Unit Range Default DescriptionS46 decimal 136 or 138 138 Controls selection of compres-sion. S46 = 136 means executeerr

55Owners ManualRegister Unit Range Default DescriptionS86 decimal 0, 4, 5, 9, 12, 13, or 14 When the modem issues aNO CARRIER result code, a value

56Model MT5600ZDXS95 - Extended Result CodesThe bits in this register can be set to override some of the Wn command options.A bit set to a 1 in this r

57Owners ManualTable 3-4 Result CodesTerse Verbose Description0OK Command executed1 CONNECT Modem connected to line2 RING Ring signal detected3 NO C

58Model MT5600ZDXTerse Verbose Description56 * CARRIER 24000 24000 bps Data Carrier Detected57 * CARRIER 26400 26400 bps Data Carrier Detected58 * CAR

59Owners Manual170 * CONNECT 42000 Connected at 42000 bps171 * CONNECT 44000 Connected at 44000 bps172 * CONNECT 46000 Connected at 46000 bps173 * CO

6Model MT5600ZDXIntroductionWelcome to the world of data communications. You have acquired oneof the finest intelligent data/fax modems available tod

60Model MT5600ZDXLocal Analog Loopback Test/V.54 Loop 3In this test, data from your computer or terminal is sent to your modem'stransmitter, con

61Owners ManualDigital Loopback Test/V.54 Loop 2 (Local/Manual)The Digital Loopback Test is an on-line test that loops data sent from onemodem across

62Model MT5600ZDXFigure 4-2. Digital Loopback Test (local/manual)6. When testing is complete, you may end the test by typing an EscapeSequence (+++

63Owners Manualcase "U" characters is a good way to send an alternating test pattern ofones and zeros. The data received by the remote mode

64Model MT5600ZDXIntroductionThis chapter starts out with statements about your modem's 10-yearwarranty (limited to customers in the U.S., Canada

65Owners Manualout the modem information (below), and have it available when you call.If your modem requires service, the tech support specialist wil

66Model MT5600ZDXSend modems to this address:MULTI-TECH SYSTEMS, INC. 2205 WOODALE DRIVEMOUNDS VIEW, MINNESOTA 55112 ATTN:

67Owners Manual2. Enter the name of the file you wish to download from the BBS.3. If a password is required, enter the password.4. Answer Y or N to t

68Model MT5600ZDXReading a MessageWhen you log on, the BBS will tell you if you have a personal message(mail). At the prompt Would you like to read it

69Owners Manual1. Put the FLM file and the new modem firmware file (e.g., V1400DS.S37)in an appropriate directory on the computers hard disk.2. Conf

7Owners ManualGeneral features include:4 Compliance with major ITU-T, TIA, and EIA international standards toensure compatibility with other modems.4

70Model MT5600ZDXRTS/CTS flow control). If the wrong format was used, reinitiate theupoad at step 5 using a correct firmware hex file.7. The Device s

71Owners ManualAppendix A Technical SpecificationsYour MultiModemZDX meets the following specifications:Tradename MultiModemZDXTMModel Numbers MT56

72Model MT5600ZDXSpeed Conversion Serial port data rates adjustable to 300, 1200, 2400,4800, 9600, 19,200, 38,400, 57,600 and 115,200bpsFlow Control S

73Owners ManualCarrier Frequencies,1270 Hz Mark, 1070 Hz Space for300 bps Transmit Originate(Bell Standard) 2225 Hz Mark, 2025 Hz Space forReceive Or

74Model MT5600ZDXAGC Dynamic Range 43 dBInterface EIA RS232C/CCITT V.24Connectors DB25 (RS232C) connector; Two RJ11 modular phonejack: for line, for t

75Owners ManualAppendix B - Regulatory InformationFCC Regulations for Telephone LineInterconnection1. This equipment complies with Part 68 of the F

76Model MT5600ZDXservice may be required. But if advance notice isnt practical, thetelephone company will notify the customer as soon as possible. Al

77Owners ManualFCC Fax UpdateThe Telephone Consumer Protection Act of 1991 makes it unlawful for anyperson to use a computer or other electronic devi

78Model MT5600ZDXpipe system, if present, are connected together. This precaution may beparticularly important in rural areas.Caution: Users should no

79Owners Manualconnections comply with ITU recommendation V28. The DTE connectionsare therefore taken to be safe voltages (less than ± 30 volts).The

8Model MT5600ZDXFax4 Supports V.17, Class 1and Class 2 Group 3 fax communicationstandards, allowing it to communicate with other fax modems as wellas

80Model MT5600ZDXii. external control software or external control apparatus which cause theoperation of the modem associated call set-up equipment to

81Owners Manuald. The user should not issue any sequence of commands to the modem which wouldcause the modem to exceed the maximum allowable pause of

82Model MT5600ZDXAppendix C - V.90 InformationThis appendix provides information on ITU V.90 support for the Multi-TechMT5600ZDX modem. It lists so

83Owners Manual

84Model MT5600ZDX

9Owners ManualSerial CableYou must provide a serial cable to connect the MultiModemZDX to yourcomputer. Serial cables are available at computer store